CSLB General Building (B) Trade Practice Test
Câu hỏi thường gặp
Có bao nhiêu câu hỏi luyện tập CSLB HVAC (C-20) Trade ở đây?+
Một ngân hàng đầy đủ câu hỏi CSLB HVAC (C-20) Trade nguyên gốc theo các lĩnh vực chính thức, có trọng số như bài thi thật, kèm giải thích. Miễn phí, không cần đăng ký.
Kỳ thi CSLB HVAC (C-20) Trade như thế nào?+
Khoảng 100 câu, 210 phút, cần 72% để đậu. Luyện theo chủ đề ở đây, rồi làm bài thi thử tính giờ để đánh giá mức sẵn sàng.
Đây có phải câu hỏi thi thật không?+
Không. Mọi câu hỏi đều 100% nguyên gốc, viết từ nguồn công khai kèm giải thích. Chúng tôi không sao chép câu hỏi thi thật hay tài liệu ôn thi trả phí.
Tôi có thể học bằng tiếng Trung hoặc tiếng Tây Ban Nha không?+
Phần luyện tập của PrepPass có tiếng Anh, 中文 và Español. Kỳ thi chính thức bằng tiếng Anh — chuyển ngôn ngữ câu hỏi sang tiếng Anh bất cứ lúc nào để làm quen thuật ngữ ngày thi.
Câu hỏi luyện tập mẫu
Một vài câu hỏi thực tế từ ngân hàng miễn phí này, kèm giải thích đầy đủ. Dùng công cụ luyện tập ở trên cho toàn bộ.
- 1. Load & Design
In residential load calculations, what does an ACCA Manual J procedure primarily determine?
- a.The size and gauge of supply ductwork
- b.The heating and cooling loads of a building based on its construction and climate
- c.The refrigerant charge required for the condenser
- d.The electrical service size for the panel
Đáp án: b
Giải thích: Manual J is the industry-standard residential load calculation method. It estimates the sensible and latent heating and cooling loads by accounting for construction, insulation, windows, orientation, infiltration, and local design temperatures. Equipment is then selected to match those calculated loads.
Nguồn: California Energy Code (Title 24)
- 2. Load & Design
Under the California Mechanical Code, when is a permit generally required for HVAC work?
- a.Only for commercial buildings
- b.Only when replacing a thermostat
- c.When installing, altering, or replacing mechanical equipment such as a furnace or air conditioner
- d.Never for residential work
Đáp án: c
Giải thích: The CMC and local jurisdictions require a mechanical permit for installing, altering, or replacing regulated equipment like furnaces, air conditioners, and ductwork. Permits trigger inspection to verify code-compliant, safe installation. Minor maintenance such as filter changes does not require a permit.
Nguồn: 2022 California Mechanical Code (CMC)
- 3. Installation
What is the primary purpose of providing combustion air to a gas-fired furnace?
- a.To cool the electronic controls
- b.To supply oxygen for complete and safe fuel combustion
- c.To increase supply air temperature
- d.To reduce refrigerant pressure
Đáp án: b
Giải thích: A gas furnace needs adequate combustion air so the burner receives enough oxygen for complete combustion. Insufficient air causes incomplete combustion, producing carbon monoxide and sooting. The CMC specifies required openings or ducts based on the appliance input and the confining space.
Nguồn: 2022 California Mechanical Code (CMC)
- 4. Installation
In a split-system heat pump, the outdoor coil functions as the condenser during which mode?
- a.Heating mode
- b.Defrost mode
- c.Cooling mode
- d.Emergency heat mode
Đáp án: c
Giải thích: In cooling mode the outdoor coil rejects heat and acts as the condenser, while the indoor coil absorbs heat as the evaporator. In heating mode the reversing valve swaps these roles. Understanding this reversal is key to installing and servicing heat pumps.
- 5. Installation
The condensate drain line from a cooling coil is often fitted with a trap to accomplish what?
- a.Add refrigerant
- b.Prevent air from being pulled through the drain and allow proper condensate flow
- c.Increase blower speed
- d.Filter the return air
Đáp án: b
Giải thích: A properly sized trap on a draw-through coil prevents the blower's negative pressure from either holding water in the pan or pulling air backward through the drain. This allows condensate to flow freely to the drain. The trap depth is based on the unit's static pressure.
- 6. Refrigeration
A thermostatic expansion valve (TXV) controls refrigerant flow into the evaporator to maintain what?
- a.Constant condenser pressure
- b.Constant compressor speed
- c.A relatively constant evaporator superheat
- d.Constant subcooling
Đáp án: c
Giải thích: A TXV modulates refrigerant flow to hold a stable superheat at the evaporator outlet, matching flow to the load. This keeps the coil fed efficiently and protects the compressor from liquid floodback. It responds to the temperature and pressure of the suction line.
- 7. Refrigeration
As a general principle, adding refrigerant charge to a properly running system tends to do what to the low-side pressure?
- a.Lower it significantly
- b.Raise it
- c.Have no effect
- d.Reverse compressor rotation
Đáp án: b
Giải thích: Adding charge generally raises system pressures, including the suction (low-side) pressure, while removing charge lowers them. Technicians interpret these trends together with superheat and subcooling. Charging must be verified against manufacturer targets, not pressure alone.
- 8. Service & Troubleshooting
A typical low-voltage control (thermostat) circuit in residential HVAC operates at what voltage?
- a.120 volts
- b.240 volts
- c.24 volts
- d.480 volts
Đáp án: c
Giải thích: Residential control circuits generally operate at 24 volts AC, supplied by a step-down transformer. The thermostat switches this low voltage to energize relays and contactors. Measuring 24 volts at the appropriate terminals helps confirm control-circuit operation.
- 9. Service & Troubleshooting
A technician measuring compressor amp draw far above the rated load amps (RLA) should suspect what?
- a.A perfectly healthy compressor
- b.A mechanical or electrical problem such as high head pressure or failing windings
- c.An oversized filter
- d.Low thermostat voltage
Đáp án: b
Giải thích: Amp draw well above the nameplate RLA indicates the compressor is overloaded, which can stem from high head pressure, low voltage, or degrading windings. Continued operation risks overheating and failure. The technician investigates head pressure, voltage, and mechanical condition.
- 10. Safety & Codes
The California Mechanical Code (CMC) primarily governs what?
- a.Electrical wiring only
- b.Plumbing fixtures only
- c.The installation of heating, ventilation, air-conditioning, and refrigeration systems
- d.Structural framing
Đáp án: c
Giải thích: The CMC sets the rules for installing mechanical systems including furnaces, air conditioners, ventilation, and refrigeration, covering venting, combustion air, clearances, and equipment access. Electrical work falls under the CEC and plumbing under the CPC. Contractors coordinate across these codes.
Nguồn: 2022 California Mechanical Code (CMC)